Readers ask: How To Make Decoupage Coasters On Tile?

Readers ask: How To Make Decoupage Coasters On Tile?

How do you decoupage tile coasters?

Instructions for Decoupage Tile Coasters

  1. Wipe the top of the tiles with a damp paper towel to remove dust and dirt.
  2. Cut the paper or fabric to fit the top of the tile.
  3. Brush a layer of Mod Podge on the tile.
  4. Gently spread a coat of Mod Podge over the whole top of the tile, including the picture.
  5. Let dry.

How do you make Mod Podge with coasters from tiles?


  1. Select your tiles and remove dirt and dust.
  2. Tear or cut paper into a square that almost, but doesn’t completely, cover the top of the tile.
  3. Add Mod Podge to the top of the tile in a medium layer.
  4. Apply a top coat of Mod Podge over the top of all tiles; let dry and apply another coat.

Can you make coasters from tiles?

Tiles Make the Best Coasters This is a project that you can easily customize to fit your personal taste and it’s a great handmade gift idea, too.

Can you decoupage coasters?

Decoupage Tile Coasters Coasters are one of those things that you can never have enough of. All you have to do is glue a square of pretty paper or fabric onto the tile and coat with waterproof decoupage medium. Quick and easy!

You might be interested:  Often asked: How To Cut Marble Tile By Hand?

What tiles to use for coasters?

Materials Needed to Make Tile Coasters:

  • 4 – 4″ White Ceramic Tiles.
  • 4 – 3.5″ pieces of scrap book paper (below is the exact scrap book paper I bought from Walmart), photos, any paper, etc.
  • Scissors.
  • Ruler.
  • 1 – 8 x 11″ Sheet of Felt.
  • 2 oz Mod Podge.
  • Foam Paint Brush.
  • Clear Spray Paint (or any other sealer)

Can you decoupage on ceramic tile?

Smooth ceramic tiles are a better choice for decoupaging, since the smooth surface resists bubbling and tearing of the image. When done properly, the decoupaged tile is waterproof and withstands normal wear and tear.

How do you seal homemade coasters?

You’re going to want to coat the image and coaster with at least three coats of Mod Podge, allowing it to dry for 15 minutes (or until clear) between coats. Once the final coat has dried, spray all of the coasters with a clear acrylic gloss spray, which ensures that they’re waterproof/drink proof.

How do you make tile coasters waterproof?

Apply 2 coats of a clear spray sealer to the coasters to seal and waterproof them. Make sure to do this in a well ventilated area. Spray the top, sides, and bottom side. Let the sealer dry for 20 minutes or so.

What do you put on the bottom of coasters?

As a final touch, attach felt squares to the bottom of your coasters with glue or double sided tape. Some craft stores even sell adhesive-backed felt which makes it super easy. You could also use cork-board instead of felt.

How do you heat proof coasters?

Finally seal your coasters with two or three coats of acrylic spray or varnish, or you could try using a clear engine lacquer which is heat resistant and helps stop hot mugs from sticking. You might find you need to ‘cure’ them for a week or two to stop them being tacky when used.

You might be interested:  Often asked: How To Install Mosaic Tile Kitchen Backsplash?

How do you make clear coasters?

  1. To make one coaster, you will need about 3 oz of resin.
  2. Add some sand to a small mixing cup.
  3. Pour the sandy resin into one third of the mold.
  4. Pour about 1 oz of resin into a mixing cup.
  5. Pour about 1 oz of resin into a mixing cup.
  6. Pour some of the blue resin into the left third of the mold.

Is Mod Podge waterproof for coasters?

This Mod Podge is water resistant and not tacky, just right for coasters. Paint a thin coat of Mod Podge onto your tile. I used a soft bristle brush, but you could use a foam brush, too. You can just wipe the Mod Podge off when it’s wet, but once the it dries, well, at least your coaster will have some texture!

Leave a Reply

Your email address will not be published. Required fields are marked *